issue no. : pc - 02 - 070 date of iss ue : november 15, 2002 classification : messrs. d igi - key delivery specification product description : balun product part number : ehf2bg2060 classification of spec : individual product specific ation applications : cellular phone for other applications, contact the undersigned in advance. term of validity : november 14, 2007 from the date of issue. customer use only this was certainly received by us. 1(one) copy is being returned to you. recei pt record#: date of receipt: received by: title: dept.: matsushita electronic components co., ltd. network device company module s trategic business unit engineering group hfd team 992 - 1 aiba ohno - cho ibi - gun gifu 501 - 0598 japan tel: +81 - 0 585 - 36 - 2322 fax: +81 - 0 585 - 36 - 2344 prepared by : h. ito c hecked by : m. mizuno authorized by : m. mizuno title : manager of engineering new change renewal
balun delivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 appearance drawing no. 151 - ehf - 2bg2060 9 - 1 [shape, appearance, dimension] unit: mm (4) (1) 2.0 + / - 0.1 0. 95+/ - 0.1 1.25+/ - 0.1 ceramic substrate sn - pb ( sn :pb=9:1) or sn ni ag - pd item appearance/ construction marking remarks description product surface shall be covered with a protective film, which does not easily separate nor present noticeable unevenness, scratches, pinholes, color changes etc. terminals shall ensure practically acceptable quality . substrate shall be as shown in the drawing with no excessive chippings, scratches, burrs, or cracks. shall be legible in black (with printing paste) . ma rked side for pin 1 . note 1) ?typ? is used where no dimensional tolerance applies. nu (6) (1) in gnd (5) (2) gnd out2 (4) (3) out1 (5) (2) (6) (3)
unit mhz db ohm ohm - db deg typ. - - 50 200 - - 180 max. 2170 1.0 - - 2.0 1.5 195 balun delivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno che ck m. mizuno plan h. ito ehf2bg2060 specification and measurement drawing no. 151 - ehf - 2bg2060 9 - 2 [absolute maximum ratings] n o. 1 2 3 item maximum input power operating temp erature storage temperature symbol pmax topr tstg rating 100 - 30?+85 - 40?+85 unit mw degc degc remarks dc voltage is 0v . note: this component cannot apply a dc bias. [ electrical characteristics ] t= - 30?+85degc no . 1 2 3 4 5 6 7 item frequency insertion loss (back to back) unbalance impedance balance impedance unbalance port vswr amplitude balance phase balance test circuit - fig - 2 - - fig - 1 fig - 1 fig - 1 min. 1920 - - - - - 1. 5 165 [ internal circuitry ] (4) out 2 (3) out 1 (1) in (2) gnd (5) gnd [ measuring circuit ] fig.1 gnd gnd gnd b a c network analyzer s - parameter test set in out < phase balance measurement > ? phase1 a=in, b=out, c=terminal resistor (50 ohm) ? phase2 a=in, c=out, b=terminal re sistor (50 ohm) ?phase balance phase balance=phase1 - phase2 < insertion loss measurement > assuming the loss as ?loss? when d=in, e=out insertion loss for a device is ?loss?/2 specification matching resistor 47 ohm e d fig. 2 gnd gnd
balun delivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 terminals/recom mended lands drawing no. 151 - ehf - 2bg2060 9 - 3 [ terminal dimensions ] unit: mm pin no . (3) 0.3 0.65 bottom view (5 ) gnd 0.35 2. 65 1.0 top view pcb pad product 0.2 0.3 tolerance of term inal dimensions : +/ - 0.15 0.35 [recommended pcb pad dimensions] unit: mm (4) (2) (5) (1) (6) 0.65 0.65 (6 ) nu 0.3 (4 ) out2 gnd (2) 0.3 in (1) out1 (3) 1.0 0.65
assemble this component on a pc board with 0.8mm thickness using the recommended soldering condition shown below, and apply a bending force of 3mm warping at a rate of 1mm/sec. 5 seconds and 5 times. judgment criteria no abnormality shall be observed in appearance or electrical characteristics . over 90% of the terminal surface shall be covered with solder . over 95% of the terminal surface shall be covered with solder . there should not be any cracks in the component or solder joints, no abnormality in electrical characteristics. test condition +85 degc, 1000 h - 40 degc, 1000 h +60 degc, 90 %rh, 1000 h +121 degc, 99%rh, 2.026x10 5 pa, 100 h - 40?+85 degc, each 30 min. , 2 00cy 10?500hz , 10g , in each direction of xyz , 2 h 30min. 100g , 6ms , half sinusoidal wave, in each direction of xyz , 3 times 1.8m , 6 faces x 6cy(36 times with 100g dummy load) 200pf, 0 ohm, +/ - 200v, each 5 times manual hot gas: 2 6 0+/ - 10degc, 30 sec., 2 times soldering iron: 260+ / - 10degc, 3 sec., 2 times reflow: 260degc peak, 2 times solder bath: 235+/ - 5degc, 2 sec. reflow: 230degc test item high temperature low temperature high - temperature high - humidity storage pressure pot temperature cycling vibration impact shock (drop) electro static discharge solder ing heat resistance solder ability board warping terminal removal seating plane co - planarity ba lun delivery specification enact. date november 15, 2002 e nfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 quality characteristics drawing no. 151 - ehf - 2bg2060 9 - 4 [ quality characteristics ] < recommended solde ring condition > diagram1 shown below is a recommended reflow soldering condition . degc 250 230 200 170 140 temperature 60~180 sec. time 30~60 sec. 3mm 45mm t=0.8mm 45mm within 0.1mm solder a component on a pc board using the recommended condition shown below and then press the component sideways at 1mm/sec. destruction limit 9.8n or greater.
balun delivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 cautions drawing no. 151 - ehf - 2bg2060 9 - 5 [ cautions for use ] (1) operating a product over the maximum rating for even a moment may result in a product failure or breakage. never use a product in such a condition that it may cause a safety problem. (2) opening or short - circuiting the product terminals or inserting a product in the reverse orientation while power is being supplied may cause a breakage. always avoid such circumstances. (3) operations in a corrosive gas atmosphere or improper environments such as high - temperature, high - humidity or dewy conditions may lead to product performance deterioration, a breakage, a change in appearance etc. please avoid such conditions, as they are unsafe. (4) always ground the soldering iron or solderi ng bath used for assembly operation to avoid any excessive voltage applied to a product. (5) after soldering with solder bridges, incomplete soldering or in the reverse orientation, supplying power may result in a product breakage. please confirm the solde red condition before supplying power to the product. (6) excessive stress on the terminals may cause a contact failure or performance deterioration. please use caution. (7) please provide a fail - safe provision in the product you design by taking any failure of our product into consideration. (8) this product does not include a dc - cutting device. application of a dc voltage between the balance port and the unbalance port may cause product deterioration or breakage. * if any question arises about the safety of this product, please contact us immediately with a request for an engineering examination. [remarks] *1: all of the materials used in this product are those listed as the existing chemical substances based on the ?law for examination and regulation of manufac ture of chemical substances? . *2: the production process of this product does not use any ozone - depleting chemicals (ozc) regulated by the montreal protocol. *3: validity of this specification is 5 years from the date of issue, but the validity is consider ed on going unless any changes are made.
balun del ivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 packaging specification 1 drawing no. 151 - ehf - 2bg2060 9 - 6 [ packaging materials ] 1. materials 1) embossed carrier tape (refer to the attachment) 2) top tape: anti - static 3) packaging box (refer to the attachment) 4) packaging tape, carrier - securing adhesive tape 2. spe cification no. 1 2 3 4 5 6 7 8 9 10 item reel outer diameter reel inner diameter reel inner width quantity in a reel taping direction top tape attachment position label attachment posi tion tape leader part and tape ending part missing products packaged quantity in a box remarks tape breaks force. min. 10n top cover tape strength. min. 10n tape peel force. 0.1?1.0 n tape peel angle. 165?180degree reel weight. max 1500g indicated item pat no., lot no. quantity, maker country of origin 84000 pieces/box(max) condition refer to the attachment . refer to the attachment . refer to the attachment . 4000 pieces/reel tape unreeling direction (with markings facing up) top tape < top tape attachment area > embossed tape top tape edge must stay inside the sprocket holes of the embossed carrier (sprocket holes shall not be covered) . tape unreeling direction label leader part no missing products shall be allowed . 21 reels/box (max) 8.0+/ - 0.2mm 5.5mm 200~220mm (product - unloaded part) 100~150mm, 25~38 pieces worth, (product - unloaded part) 3 00 ~ 4 00mm ending part product - loaded part top tape embossed carr ier
balun delivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 packaging specification 2 drawing no. 151 - ehf - 2bg2060 9 - 7 1. method 1) load products in each cavity of an embossed carrier tape, in the correct orientation, by leaving the pro duct - unloaded part shown in item no. 8(p9 - 6) of the packaging specification. 2) heat - seal a top tape in good alignment on the carrier tape. 3) after 4000 pieces are loaded and reeled, provide a product - unloaded part at the tape - leader portion. secure the t ip of the carrier tape with a piece of adhesive tape. 4) stack the reels (21 reels max.) and enclose them in a packaging box. close the flaps with a piece of adhesive tape. 5) provide markings on the packaging box. < items to be indicated > 1. part no. 2. quantity 3. lot no. 4. manufacturer name 5. country of origin * insert cushion material in the empty spaces to s ecure reels . number of stacking, 21 reels max. packaging box shape varies with the number of reels enclosed . reel label marking on the packaging box
balun delivery specification enact. date november 15, 2 002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 packaging specification 3 drawing no. 151 - ehf - 2bg2060 9 - 8 [embossed tape dimensions] unit: mm 0.25 +/ - 0.05 (5.0deg) 4 +/ - 0 .1 2 +/ - 0.0 5 d 1.0 d 1.5 +0.1 - 0 (5.0deg) 1.0 5 +/ - 0.1 4 +/ - 0 .1 1.45 +/ - 0.1 8 +/ - 0. 2 2 .25 +/ - 0.1 3.5 + / - 0. 05 1.75 +/ - 0.1 +0. 2 - 0 (1) unspecified corner radius shall be 0.3mm max. (2) cumulative pitch error of sprocket holes shall be +/ - 0.2mm for 10 pitches.
balun delivery specification enact. date november 15, 2002 enfo. date november 15, 2002 p.s.m ----- approval m. mizuno check m. mizuno plan h. ito ehf2bg2060 packaging specification 4 drawing no. 151 - ehf - 2bg2060 9 - 9 [ reel dimensions ] unit: mm (1) this reel conforms to eiaj - rrm - 08b based on eiaj standard . (2) material: ps (polystyrene) number ? 44 ? 44 ? 3 r85 a ? 180 0 -3 h n ? 60 +1 0 ? 13 b 3 b 3 b w1 w2 h 3 5 4 110 105 0.8 0.6 0.4 0.2 0.8 0.6 0.4 0.2 scale ? 3 2 min 18.0 3 ? } 0. 2 2 min 18.0 2 min 18.0 2 ? } 0. 2 r10.5 ? } 0.4 ? 10 120 ? ? ? } 0.2 120 ? ? ? } 0.2 r0.5 2-r1 2-r1 rim , hub rim a hub n 180 0 -3 60 +1 0 inner width , outer width tape width inner width w1 outer width w2 8 9 +/- 0.3 11 +/-1.0 center area label 105...50
|
